SEM203W

Manual range configuration, suitable for Potentiometer sensors

• Suitable For 1K to 100K Potentiometer
• Push Button Configuration
• LED Over-range Indication
• Push Button Sensor Matching
• High Stability

The SEM203W potentiometer transmitter is an in-head transmitter that accepts potentiometer sensors and converts the sensor output over a configured range to a standard industrial (4 to 20) mA transmission signal. A simple push button operation allows the user to select the desired transmitter range manually, by setting the slide wire position and pressing button to store at both the (4 and 20) mA points.

FEATURE HIGHLIGHTS

PUSH BUTTON CONFIGURATION
A single push button and LED indicator allows the user configure transmitter range against a manually setinput condition. A red LED is included to help guide the user. The LED also operates as a sensor error indicator.

STABILITY
The SEM203W in head transmitter incorporates the latest digital technology to ensure accurate, low drift
performance.

FAST RESPONSE
The SEM203W takes less than 50 ms to reach 70% of its final output value for a change of the input signal.

POTENTIOMETER

Any value of potentiometer can be used between 1 and 100K ohms

SEM203TC

Manual range configuration, suitable for thermocouple sensors

• K, J, N, E, T,R, S thermocouples plus mV
• Simple push button configuration
• Isolation Input to Output
• Vibration Tested
• No PC needed

The SEM203TC is a cost effective in head transmitter that accepts thermocouple temperature sensors. It converts the thermocouple sensor output over a configured range, to a standard industrial (4 to 20) mA transmission signal.

A simple push button operation (meaning no PC is required) allows the user to select TC type, burnout direction and select fixed ranges and trim the (4 and 20) mA points. If required the desired range can be specified at the time of order, removing the need for user configuration.

The thermocouple temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost. Otherwise the range is not specified then the transmitter will be shipped with the default range of (0 to 1000) °C type K

SEM206P

Programmable, suitable for Pt100 temperature probes

• Suitable For Pt100 Sensors
• Programmable Temperature Range
• Over range LED indication
• Vibration Tested

The SEM206P is a cost effective “smart” in head transmitter that accepts PT100 temperature sensors.

It converts sensor output over a configured range, to a standard industrial (4 to 20) mA transmission signal.

PC configuration allows the user to select range, units and burnout direction, without requiring calibration
equipment. Configuration is performed quickly using our USB port driven configurator by simply connecting two clips
to the SEM206P loop terminals and following the software instructions. Calibration set up may be saved as a file on
the PC for later use. If required, the desired range can be specified at the time of order, removing the need for user configuration.

The pt100 temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost. Otherwise the range is not specified then the transmitter will be shipped with the default range of Pt100 0/100 deg C

FEATURE HIGHLIGHTS

SENSOR REFERENCING
The SEM206P sensor referencing via the Windows based USBSpeedlink software allows for close matching
to a known reference sensor eliminating possible sensor errors.

SENSOR BURN OUT DETECTION
If a sensor wire is broken or becomes disconnected the SEM206P output will automatically go to its user
defined level upscale or downscale and the LED illuminates.

STABILITY

The SEM206P in head transmitter incorporates the latest digital technology to ensure accurate, low drift
performance.

LED WARNING

If the SEM206P detects the sensor is out of range, then a red LED will illuminate in the transmitter to alert the user that something is wrong.

SEM203P

Manual range configuration, suitable for Pt100 sensors

• Suitable For Pt100 Sensors
• Push Button Configuration
• LED Over-range Indication
• Push Button Sensor Matching
• No PC Needed

The SEM203P is a push button configurable in-head temperature transmitter that accepts PT100 temperature sensors. It
converts the sensor output over a configured temperature range, to a standard industrial (4 to 20) mA transmission signal.
A simple push button operation (meaning a PC is not required for configuration), allows the user to not only select the desired range and burnout direction but also perform user trim at both (4 and 20) mA points.

If required, the desired range can be specified at the time of order, removing the need for user configuration.

The pt100 transmitter can be ordered with any of our temperature probes and connection heads. We can supply temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost. Otherwise the range is not specified then the transmitter will be shipped with the default range of Pt100 0/100 deg C

SEM206PV

Pt100 temperature transmitter with voltage output

• Suitable for Pt100 temperature sensors
• 3 wire (0 to 10) volt output
• PC Programmable
• High stability

The SEM206PV is a cost-effective digital in-head transmitter that accepts Pt100 temperature sensors and converts
sensor output over a configured range to a standard industrial (0 to 10) V control signal. The output is linear to
temperature.

PC configuration allows the user to select Range and Burnout direction, without requiring calibration equipment.
Configuration is performed quickly using our USB port-driven configurator by simply connecting two clips to the
SEM206PV power terminals and following the software instructions. Calibration set up may be saved as a file on the
PC for later use.

If required, the desired range can be specified at the time of order, removing the need for user configuration. If the range
is not specified, then the transmitter will be shipped with the default range of (0 to 100) °C and upscale burnout.

SENSOR CORRECTION
The SEM206PV sensor referencing via, the Windows based USB-Speedlink software, allows for close
matching to a known reference sensor, reducing possible sensor errors.

SENSOR BURN-OUT DETECTION
If a sensor wire is broken or becomes disconnected, the SEM206PV output will automatically go to its user-defined level upscale or downscale.

STABILITY
The SEM206PV in-head transmitter incorporates digital technology to ensure accurate, low-drift
performance.

SEM206THV

Temperature transmitter with thermistor, Pt1000, Pt500 input and voltage output

• Suitable for Thermistor, Pt1000 or Pt500 temperature sensors.
• Other sensors available from our library available here.
• 3 wire (0 to 10) volt output.
• PC Programmable.

The SEM206THV is an in-head transmitter that accepts thermistor temperature sensors as well as Pt1000 and Pt500
RTDs and converts the sensor output over a configured range to a standard industrial (0 to 10) Volt output signal.

The output signal is linear to temperature. PC configuration allows the user to select Range and Burnout direction, without requiring calibration equipment. Configuration is performed quickly using our USB port-driven configurator by simply connecting two clips to the SEM206THV power terminals and following the software
instructions.

Calibration set up may be saved as a file on the PC for later use. The output signal is linear to temperature. A variety of
thermistor types are available when using USB-SpeedLink configuration software. Please consult your supplier for
custom thermistors.

SENSOR REFERENCING
The SEM206THV sensor referencing, via the Windows based USB-Speedlink software, allows for close
matching to a known reference sensor, eliminating possible sensor errors.

SENSOR BURN-OUT DETECTION
If a sensor wire is broken or becomes disconnected, the SEM206THV output will automatically go to its user-defined level, upscale or downscale.

STABILITY
The SEM206THV in-head transmitter incorporates the latest digital technology to ensure accurate, low-drift
performance.

SENSOR LIBRARY
The Thermistor or Pt sensor type required, is loaded onto the SEM206THV from a software library using the USB-Speedlink
software. The sensor library can be added to as new sensors become available or are requested.
Thermistor sensors with a resistance value up to 100 K Ohms at 25 °C can normally be accommodated.

SEM206TH

Temperature transmitter suitable for Thermistor or Pt1000 sensors

• Accepts Thermistor or Pt1000 sensors.
• Other sensors available from our library available here.
• 4 to 20mA loop powered output.
• Sensor offset function.
• Custom thermistors available.

The SEM206TH thermistor temperature transmitter accepts thermistor or Pt1000 temperature sensors and converts the sensor output over a configured range to a standard industrial (4 to 20) mA transmission signal. The output signal is linear to temperature. A variety of thermistor types are available when using USB SpeedLink configuration software. Please consult your supplier for custom thermistors. In addition to the PC configuration feature, simple push button operation allows the user to select the desired temperature range manually, by either simulating the thermistor temperature with a resistance box or setting the thermistor sensor to the required calibration point and pressing button to store at both 4 mA and 20 mA points.

The thermistor temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply temperature probe assemblies with your required thermistor and the thermistor temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost.

FEATURE HIGHLIGHTS

SENSOR CORRECTION
The SEM206TH sensor correction function via the Windows based USBSpeedlink software allows for close matching to a known reference sensor eliminating possible sensor errors.

SENSOR BURN OUT DETECTION
If a sensor wire is broken or becomes disconnected the SEM206TH output will automatically go to its user defined level upscale or downscale and the LED illuminates.

STABILITY
The SEM206TH in head transmitter incorporates the latest digital technology to ensure accurate, low drift performance.

PC / PUSH BUTTON CONFIGURATION
PC configuration requires USB SpeedLink software together with a USB configuration kit. The software allows the operator to select from a variety of thermistor types, then set the required temperature range for a (4 to 20) mA output. A single push button and LED indicator allows the user to configure transmitter range against a manually set input condition.

SEM206TC

Programmable, suitable for thermocouple sensors

• K, J, N, E, T, R, S thermocouples plus mV
• Isolated input to output
• Over range LED indication
• Programmable burnout

The SEM206TC thermocouple temperature transmitter is a cost effective “smart” in head transmitter that accepts thermocouple temperature sensors. It converts the sensor output over a configured range, to a standard industrial (4 to 20) mA transmission signal.

PC configuration allows the user to select TC type, range, units and burnout direction, without requiring calibration
equipment. Configuration is performed quickly using a our USB port driven configurator by simply connecting two
clips to the SEM206TC loop terminals and following the software instructions. Calibration set up may be saved as a
file on the PC for later use. If required the desired range can be specified at the time of order, removing the need for user configuration.

The product also comes with a calibration feature so both the offset and span can be adjusted to match a particular temperature sensor when applied to a known reference temperature.

The thermocouple temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost. Otherwise the range is not specified then the transmitter will be shipped with the default range of (0 to 1000) °C type K

FEATURE HIGHLIGHTS

SENSOR REFERENCING
The SEM206TC sensor referencing via the Windows based USBSpeedlink software allows for close matching to a known reference sensor eliminating possible sensor errors.

SENSOR BURN OUT DETECTION
If a sensor wire is broken or becomes disconnected the SEM206TC output will automatically go to its user defined level upscale or downscale.

STABILITY
The SEM206TC in head transmitter incorporates the latest digital technology to ensure accurate, low drift performance.

LED WARNING

If the SEM206TC detects the sensor is out of range, then a red LED will illuminate in the transmitter to alert the user that something is wrong.

TTR200 and TTR200X

Suitable for RTD, potentiometer and resistance sensors. UKEX, ATEX and IECEx versions available.

• Suitable for RTD, Potentiometer and Resistance Sensors
• UKEX, ATEX, IECEx Versions Available
• Sensor Calibration Feature
• User Linearisation
• Vibration Tested

The TTR200 RTD temperature transmitter accepts wide range of RTD sensors including Pt100, Pt500, Pt1000, Potentiometer, and Resistance sensors. It generates an industry standard (4 to 20) mA transmission signal across a programmed process range.  There is a version, (TTR200X), approved for use in hazardous areas and is approved to ATEX, IECEx and UKEX

The product can be easily programmed using our free USB Speedlink software and a standard USB lead (safe area version). Used with potentiometer and mV inputs, a linearisation feature is available allowing the mA output to act as required over 22 points of the input signal.  It comes with a calibration feature so both the offset and span can be adjusted to match a particular temperature sensor when applied to a known reference temperature.

This RTD temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply safe area probe assemblies or ExD and Exia approved temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost.

TTC200 and TTC200X

Suitable for Thermocouple sensors, with ATEX version

• K, J, N, E, T, R, S, L, U, B, C(W5), D(W3), G(W) plus mV Inputs
• Sensor Calibration Feature
• Isolated 4/20mA Output
• UKEX, ATEX, IECEx Versions For Hazardous Areas
• Vibration Tested

The TTC200 thermocouple temperature transmitter accepts most commonly used thermocouple and mV sensors. It generates an industry standard (4 to 20) mA transmission signal over a programmed process range. There is a version, (TTC200X) approved for use in hazardous areas and is approved to ATEX, IECEx and UKEX.

The product can be easily programmed using our free USB Speedlink software and a standard USB lead (safe area version). The mV input also has a linearisation feature allowing the mA output to act as required over 22 points of the input signal.

Isolation is a standard feature to overcome any potential ground loop effects and a sensor referencing facility enables the transmitter to be calibrated to a particular sensor.

The product also comes with a calibration feature so both the offset and span can be adjusted to match a particular temperature sensor when applied to a known reference temperature.

This thermocouple temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply safe area probe assemblies or ExD and Exia approved temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost.

SEM210 and SEM210X

Universal, Dual Input, High Performance

• Dual RTD, Thermocouple, Potentiometer and mV Inputs
• UKEX, ATEX, IECEx Approved Versions For Hazardous Areas
• Isolated Input to Output 4kV DC Flash Tested
• Maths Functions Between Inputs
• SIL 2 Hardware Safety Integrity

The SEM210 universal temperature transmitter accepts most commonly used Pt100, thermocouple, mV and potentiometer sensors. It generates an industry standard (4 to 20) mA transmission signal over a programmed process range. There is a version, (SEM210X) approved for use in hazardous areas and is approved to ATEX, IECEx and UKEX The product can be easily programmed using our free USB Speedlink software and a standard USB lead (safe area version).

Isolation is a standard feature to overcome any potential ground loop effects and a sensor referencing facility enables the transmitter to be calibrated to a particular sensor.

This universal temperature transmitter has two sensor inputs. This allows the connection of two sensors enabling maths functions, such as difference, average, highest, lowest, sensor redundancy (TC and mV only) are available. The math function of both inputs is then reflected in the single 4 to 20mA output.

The product also comes with a calibration feature so both the offset and span can be adjusted to match a particular temperature sensor when applied to a known reference temperature.

The universal temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply safe area probe assemblies or ExD and Exia approved temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost.

SEM310 and SEM310X

Universal, Dual Input, High Performance HART Temperature Transmitter

• HART 5,6,7 Compatible
• Dual RTD, Thermocouple, Potentiometer and mV Inputs
• UKEX, ATEX, IECEx Versions for Hazardous Areas
• Isolated Input to Output 4kV DC Flash Tested
• Maths Functions Between Inputs
• SIL 2 Hardware Safety Integrity

The SEM310 HART (generic device) temperature transmitter is a universal device which accepts most commonly used Pt100, thermocouple, mV , potentiometer sensors. There is a version, (SEM310X) approved for use in hazardous areas and approved to ATEX, IECEx and UKEX.  It generates an industry standard (4 to 20) mA transmission signal over a programmed process range or can be used in HART multi drop mode. Compatible to HART 5, 6, or 7 the product can be easily programmed using our free USB Speedlink software and a standard USB lead (safe area version). It can also be programmed via a HART communication device / system.

Isolation is a standard feature to overcome any potential ground loop effects and a sensor referencing facility enables the transmitter to be calibrated to a particular sensor.

This HART temperature transmitter has two sensor inputs. This allows the connection of two sensors enabling maths functions, such as difference, average, highest, lowest, sensor redundancy (TC and mV only) are available. The math function of both inputs is then reflected in the single 4 to 20mA output.

The product also comes with a calibration feature so both the offset and span can be adjusted to match a particular temperature sensor when applied to a known reference temperature.

The HART temperature transmitter can be ordered with any of our temperature probes and connection heads. We can supply safe area probe assemblies or ExD and Exia approved temperature probe assemblies with the temperature transmitter included.

If you already know the specification you require, we can configure the product for you at no extra cost.

SEM710TM

Temperature Transmitter With Display For Pt100, Thermocouple Sensors and 4 20mA Signals

• Suitable for Pt100 or thermocouple sensors
• 4 to 20mA signal input (External powered)
• 6 digit LCD display
• 4 to 20 mA loop powered output

The SEM710TM is a two wire (4 to 20) mA temperature transmitter with display, designed to accept RTD or
Thermocouple temperature sensors or a mA control signal.  Select your temperature probe here

The device displays the sensor temperature in °C or °F or mA process value on a 6-digit LCD display. Configuration is achieved by operating three-push buttons and navigating a menu structure. USB and contactless (NFC) interfaces are also provided for configuration and data logger function, with up to 5000 time-stamped logs at adjustable rates. The indicator also has an alert LED for signal error indication

Ideal for indicating the process value at the point of measurement.  The display can also be configured to read the loop signal in mA if required.

It is available in the following housings

• SCH4 connection head in ABS plastic
• SCH15 Stainless steel connection head.

DATA LOGGING FUNCTION (See Logger* entries, check website for latest Android version compatibility).

The SEM710TM temperature transmitter with display also provides a powerful data logging function. The log points can be set up to 5000 points. Each point is time and date-stamped. The SEM710TM can continue to record time-stamp data for over 4 hours on the loss of the loop supply and resumes logging when repowered. The log rate is selectable in
steps. The start of log can be delayed if required. Either fixed or rolling logs may be performed.

USB, NFC, AND PUSH-BUTTON CONFIGURATION
Configuration of the SEM710TM can be done in three ways:

• On a Windows PC running Status Instruments’ free “USB-SpeedLink” software.
• Using a suitable Android device running Status Instruments’ free NFC Configuration App “NFC-Link”.
• By use of push buttons.

USER-LINEARISATION (mA)
The SEM710TM has a user linearization function.
When using a mA input, a 22-point user-linearisation tool is available for applications such as volume in a
non-linear tank or correcting known errors in any (4 to 20) mA signal.
This can also be used to apply calibration points for loop sensors that may drift over time

SEM320X/55

UKEX, ATEX, IECEx Approved HART Field Temperature Transmitter

• HART 5,6,7 compatible
• UKEX, ATEX and IEC Ex approval
• process value, text and bar-graph displays
• (4 to 20) ma or hart multidrop output
• SIL 2 hardware safety integrity

The SEM320X is a HART (generic device) field temperature transmitter that is HART 5,6,7 compatible, universal temperature transmitter with display. It accepts RTD, Thermocouple, Potentiometer or millivolt input signals and converts them to the industry standard (4 to 20) mA transmission signal. Alternatively, HART multidrop mode can be selected.

It is approved to UKEX, ATEX and IECEx and is housed in its own bespoke connection head, Exia or ExD approved. It is programmed using a communication lead (USBX Config) together with our free configuration USBSpeedlink software, (In the safe area). Standard HART features can also be programmed using HART communication.

The HART field temperature transmitter has a rotational five-digit display for the process value and a 5-digit display for messaging, in addition to a bar graph for % of mA output.

Is is used together with our temperature probes. We can manufacture these to your specification. The most popular types can be seen here

SENSOR-REFERENCING

The SEM320 sensor-referencing, via the Windows based USBSpeedlink software, allows for close matching to a known reference sensor, eliminating possible sensor errors.

USER-CALIBRATION

In addition to sensor-referencing, current output trimming is possible via the USB and HART commands.

CUSTOM LINEARISATION

The SEM320 can be programmed with a custom linearisation to suit non-standard sensors, or sensors with unusual or unique characteristics. Consult the sales office for details.

SENSOR BURN-OUT DETECTION

If a sensor wire is broken or becomes disconnected, the SEM320 output will automatically go to its user-defined level (upscale or downscale) or pre-set value.

OUTPUT CURRENT PRESET

For ease of system calibration and commissioning, the output can be set to a pre-defined level anywhere within the (4 to 20) mA range.

SEM320/55

HART Field Temperature Transmitter

• hart 5,6,7 compatible
• process value, text and bar-graph displays
• dual inputs with maths functions (4 to 20) ma or hart multidrop output
• SIL II hardware safety integrity

The SEM320 is a HART (generic device) field temperature transmitter that is HART 5,6,7 compatible,  universal temperature transmitter with display. It accepts RTD, Thermocouple, Potentiometer or millivolt input signals and converts them to the industry standard (4 to 20) mA transmission signal. Alternatively, HART multidrop mode can be selected.

Housed in its own bespoke connection head, it is programmed using a communication lead (USB Config) together with our free configuration USBSpeedlink software. Standard HART features can also be programmed using HART communication.

The HART field temperature transmitter has a rotational five-digit display for the process value and a 5-digit display for messaging, in addition to a bar graph for % of mA output.

Is is used together with our temperature probes. We can manufacture these to your specification. The most popular types can be seen here

SENSOR-REFERENCING

The SEM320 sensor-referencing, via the Windows based USBSpeedlink software, allows for close matching to a known reference sensor, eliminating possible sensor errors.

USER-CALIBRATION

In addition to sensor-referencing, current output trimming is possible via the USB and HART commands.

CUSTOM LINEARISATION

The SEM320 can be programmed with a custom linearisation to suit non-standard sensors, or sensors with unusual or unique characteristics. Consult the sales office for details.

SENSOR BURN-OUT DETECTION

If a sensor wire is broken or becomes disconnected, the SEM320 output will automatically go to its user-defined level (upscale or downscale) or pre-set value.

OUTPUT CURRENT PRESET

For ease of system calibration and commissioning, the output can be set to a pre-defined level anywhere within the (4 to 20) mA range.